Move to _data along with some misc clean-up.

README.md

@@ -0,0 +1,39 @@
+# esphome
+
+## esp32
+
+[docs](https://esphome.io/guides/getting_started_command_line.html)
+
+Just start with an existing yaml, such as base_esp32.yaml.
+
+Plug it in to laptop, then run:
+
+```sh
+docker run --rm -v "${PWD}":/config --device=/dev/ttyUSB0 -it esphome/esphome base_esp32.yaml run
+```
+
+Then set static IP in router.
+Then in [esphome on server](http://wildebeest:6052/) create same thing, add static IP block, then upload.
+Should now be online.
+
+## Hardware
+
+### irf520
+
+[pin-out](https://protosupplies.com/product/irf520-n-ch-mosfet-module/)
+
+#### 1 x 3 Male Header
+
+SIG = Signal input (active HIGH).  Typically used with 5V logic.  Can be driven at up to 10V to fully turn on the IRF520.
+VCC = No connection
+GND = Digital ground.
+
+#### 1 x 2 Screw Terminal (Load)
+
+V+ = Connect to positive lead of load (motor, LEDs, fan, etc)
+V- = Connect to negative lead of load
+
+#### 1 x 2 Screw Terminal (Power)
+
+VIN = Connect to power supply (0-24V) being used to power the load
+GND = Connect to power supply ground

_data/pj_3_duct_fan_pwr.yaml

@@ -0,0 +1,83 @@
+substitutions:
+  device_name: "pj_3_duct_fan_pwr"
+  friendly_name: "Prj 3 Duct Fan Pwr"
+
+esphome:
+  name: pj_3_duct_fan_pwr
+  platform: ESP8266
+  board: esp01_1m
+
+wifi:
+  ssid:         "kungle-oss"
+  password:     "hcfU8@gG&8Hm"
+  fast_connect: true
+
+  manual_ip:
+    static_ip: 192.168.35.240
+    gateway:   192.168.35.1
+    subnet:    255.255.255.0
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Pj 3 Duct Fan Pwr"
+    password: "ImgAxoEGSc90"
+
+captive_portal:
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+
+ota:
+
+binary_sensor:
+  - platform: gpio
+    pin:
+      number: GPIO4
+      mode: INPUT_PULLUP
+      inverted: True
+    name: "${friendly_name} Button"
+    id: "${device_name}_button"
+    on_press:
+      - switch.toggle: "${device_name}_relay"
+  - platform: status
+    name: "${friendly_name} Status"
+    id: "${device_name}_status"
+
+switch:
+  - platform: gpio
+    name: "${friendly_name} Relay"
+    id: "${device_name}_relay"
+    pin: GPIO14
+    on_turn_on:
+      - output.turn_on: led
+    on_turn_off:
+      - output.turn_off: led
+
+status_led:
+  pin:
+    number: GPIO12
+    inverted: yes
+
+output:
+  - platform: gpio
+    pin: GPIO13
+    inverted: true
+    id: led
+
+sensor:
+  - platform: wifi_signal
+    name: "${friendly_name} WiFi signal"
+    id: "${device_name}_wifi_signal"
+    update_interval: 60s
+  - platform: uptime
+    name: "${friendly_name} Uptime"
+    id: "${device_name}_uptime"
+    update_interval: 60s
+
+text_sensor:
+  - platform: version
+    name: "${friendly_name} ESPHome Version"
+    id: "${device_name}_esphome_version"

attic_2_fan.yaml.0

@@ -0,0 +1,55 @@
+esphome:
+  name: attic_2_fan
+  platform: ESP8266
+  board: esp01_1m
+
+wifi:
+  ssid: kungle-ot
+  password: ThingsWelcomeToKungle
+
+  manual_ip:
+    static_ip: 192.168.37.70
+    gateway: 192.168.37.1
+    subnet: 255.255.255.0
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+
+ota:
+
+
+binary_sensor:
+  - platform: gpio
+    pin:
+      number: GPIO4
+      mode: INPUT_PULLUP
+      inverted: True
+    name: "Attic 2 Fan button"
+    on_press:
+      - switch.toggle: relay
+
+switch:
+  - platform: gpio
+    name: "Attic 2 Fan relay"
+    pin: GPIO14
+    id: relay
+
+status_led:
+  pin:
+    number: GPIO12
+    inverted: yes
+
+sensor:
+  - platform: wifi_signal
+    name: "Attic 2 Fan WiFi signal"
+    update_interval: 60s
+
+  - platform: uptime
+    name: "Attic 2 Fan uptime"
+
+text_sensor:
+  - platform: version
+    name: "Attic 2 Fan ESPHome version"

base_esp32.yaml

@@ -0,0 +1,24 @@
+esphome:
+  name: base_esp32
+  platform: ESP32
+  board: esp32doit-devkit-v1
+
+wifi:
+  ssid: "kungle-oss"
+  password: "hcfU8@gG&8Hm"
+  fast_connect: true
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Server 2 Fallback Hotspot"
+    password: "kRzC55vFjigT"
+
+captive_portal:
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+
+ota:

base_esp8266.yaml

@@ -0,0 +1,24 @@
+esphome:
+  name: esp8266
+  platform: ESP8266
+  board: esp01_1m
+
+wifi:
+  ssid: "kungle-oss"
+  password: "hcfU8@gG&8Hm"
+  fast_connect: true
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "esp8266 Fallback Hotspot"
+    password: "kRzC55vFjigT"
+
+captive_portal:
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+
+ota:

pj_3_duct_fan_pwr.yaml

@@ -1,6 +1,5 @@
 substitutions:
-  device_name: "pj_3_duct_fan_pwr"
+  dev_name: "pj_3_duct_fan_pwr"
-  friendly_name: "Prj 3 Duct Fan Pwr"
 
 esphome:
   name: pj_3_duct_fan_pwr
@@ -38,46 +37,28 @@ binary_sensor:
       number: GPIO4
       mode: INPUT_PULLUP
       inverted: True
-    name: "${friendly_name} Button"
+    name: "${dev_name} button"
-    id: "${device_name}_button"
     on_press:
-      - switch.toggle: "${device_name}_relay"
+      - switch.toggle: relay
-  - platform: status
-    name: "${friendly_name} Status"
-    id: "${device_name}_status"
 
 switch:
   - platform: gpio
-    name: "${friendly_name} Relay"
+    name: "${dev_name} relay"
-    id: "${device_name}_relay"
     pin: GPIO14
-    on_turn_on:
+    id: relay
-      - output.turn_on: led
-    on_turn_off:
-      - output.turn_off: led
 
 status_led:
   pin:
     number: GPIO12
     inverted: yes
 
-output:
-  - platform: gpio
-    pin: GPIO13
-    inverted: true
-    id: led
-
 sensor:
   - platform: wifi_signal
-    name: "${friendly_name} WiFi signal"
+    name: "${dev_name} WiFi signal"
-    id: "${device_name}_wifi_signal"
-    update_interval: 60s
-  - platform: uptime
-    name: "${friendly_name} Uptime"
-    id: "${device_name}_uptime"
     update_interval: 60s
 
-text_sensor:
+  - platform: uptime
-  - platform: version
+    name: "${dev_name} uptime"
-    name: "${friendly_name} ESPHome Version"
+
-    id: "${device_name}_esphome_version"
+# text_sensor:
+#   - platform: version

rack_3_duct_fan_pwr.yaml.0

@@ -0,0 +1,23 @@
+esphome:
+  name: rack_3_duct_fan_pwr
+  platform: ESP8266
+  board: esp01_1m
+
+wifi:
+  ssid: "kungle-ot"
+  password: "ThingsWelcomeToKungle"
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Rack 3 Duct Fan Pwr"
+    password: "sbIiBVpW39Zb"
+
+captive_portal:
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+
+ota: