Total overhaul - still need to rework racks.

_data/fountain_outside.yaml

@@ -0,0 +1,122 @@
+substitutions:
+  device_name: fountain-outside
+  dn: fountain_outside
+  friendly_name: Fountain Outside
+  device_description: Energy Monitoring Smart Plug with button, blue LED, and red LED.
+
+<<: !include .common.yaml
+<<: !include .esp8266.yaml
+<<: !include .wifi-oss.yaml
+
+# Enable time component for use by daily power sensor
+time:
+  - platform: homeassistant
+    id: homeassistant_time
+
+binary_sensor:
+  - platform: gpio
+    pin:
+      number: GPIO1
+      mode: INPUT_PULLUP
+      inverted: True
+    name: ${friendly_name} button
+    on_multi_click:
+      - timing:
+          - ON for at most 1s
+          - OFF for at most 1s
+          - ON for at most 1s
+          - OFF for at least 0.2s
+        then:
+          - logger.log: "Double Clicked"
+          - switch.toggle: relay2
+      - timing:
+          - ON for 1s to 2s
+          - OFF for at least 0.5s
+        then:
+          - logger.log: "Single Long Clicked"
+      - timing:
+          - ON for at most 1s
+          - OFF for at least 0.5s
+        then:
+          - logger.log: "Single Short Clicked"
+          - switch.toggle: relay1
+
+switch:
+  - platform: gpio
+    name: ${friendly_name} relay
+    pin: GPIO12
+    id: relay1
+  - platform: gpio
+    name: ${friendly_name} Light relay
+    pin: GPIO14
+    id: relay2
+
+status_led:
+  pin:
+    number: GPIO3
+    # inverted: yes
+
+sensor:
+  - platform: wifi_signal
+    name: ${friendly_name} WiFi signal
+    update_interval: 60s
+
+  - platform: uptime
+    name: ${friendly_name} uptime
+
+# Reports the Current, Voltage, and Power used by the plugged-in device (not counting this plug's own usage of about 0.7W/0.02A, so subtract those when calibrating with this plugged into a Kill-A-Watt type meter)
+  - platform: hlw8012
+    sel_pin:
+      number: GPIO13
+      inverted: True
+    cf_pin: GPIO4
+    cf1_pin: GPIO5
+    current_resistor: 0.001 #The value of the shunt resistor for current measurement. Defaults to the Sonoff POW’s value 0.001 ohm. Verified on https://fccid.io/2AKBP-X10S/Internal-Photos/X10S-Int-photo-4308983 that we use "R001" = 0.001 ohm
+    voltage_divider: 2351 #The value of the voltage divider on the board as (R_upstream + R_downstream) / R_downstream. Defaults to the Sonoff POW’s value 2351. From the pic we use 2x "125" = 2x 1.2Mohm for R_upstream and "102" = 1kohm for R_downstream, so (1,200,000+1,200,000+1,000)/1,000 = 2401
+    # but those don't fix the measurement values, probably because we actually have a BL0937 chip instead of a HLW8012, (and part variance aswell) so we have to manually calibrate with a known load or a load and a Kill-A-Watt type meter. My values used below will only be +/-10% of yours I think.
+    # The comments about the voltage divider were taken from the AWP04L template. I was unable to verify the voltage divider in the Aoycocr X10S plug.
+    power:
+      name: ${friendly_name} Power
+      unit_of_measurement: W
+      id: wattage
+      filters:
+        - calibrate_linear:
+            # Map 0.0 (from sensor) to 0.0 (true value)
+            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
+            - 1379.1 -> 200.0 # Tested outdoor fountain pump via Kill-A-Watt
+            - 2816.9 -> 411.0 # Tested blow-dryer low via Kill-A-Watt
+            - 9250.6 -> 1341.0 # Tested water boiler via Kill-A-Watt
+            - 10736.7 -> 1562.0 # Tested blow-dryer high via Kill-A-Watt
+    current:
+      name: ${friendly_name} Current
+      unit_of_measurement: A
+      filters:
+        - calibrate_linear:
+            # Map 0.0 (from sensor) to 0.0 (true value)
+            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
+            - 2.07 -> 1.67 # Tested outdoor fountain pump via Kill-A-Watt
+            - 4.18 -> 3.41 # Tested blow-dryer low via Kill-A-Watt
+            - 14.37 -> 11.64 # Tested water boiler via Kill-A-Watt
+            - 16.26 -> 13.12 # Tested blow-dryer high via Kill-A-Watt
+    voltage:
+      name: ${friendly_name} Voltage
+      unit_of_measurement: V
+      filters:
+        - calibrate_linear:
+            # Map 0.0 (from sensor) to 0.0 (true value)
+            - 0.0 -> 0.0
+            - 355.9 -> 120.6 #Tested using a Kill-A-Watt meter, value while connected LED bulb was on
+    # change_mode_every: 3 # 1 - Skips first reading after each change, so this will double the update interval. Default 8
+    # update_interval: 3s # 10s - 20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s
+
+# Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  - platform: total_daily_energy
+    name: ${friendly_name} Total Daily Energy
+    power_id: wattage
+    filters:
+        - multiply: 0.001  ## convert Wh to kWh
+    unit_of_measurement: kWh
+
+text_sensor:
+  - platform: version
+    name: "Fountain 1 ESPHome version"