216 lines
5.9 KiB
YAML
216 lines
5.9 KiB
YAML
substitutions:
|
|
duct_fan_pin: GPIO14
|
|
duct_fan_spd_name: Prj3 Duct Fan Speed
|
|
duct_fan_target_spd_in_name: Prj3 Duct Fan Target Speed In
|
|
duct_fan_target_spd_prj_name: Prj3 Duct Fan Target Speed Prj
|
|
duct_fan_target_spd_out_name: Prj3 Duct Fan Target Speed Out
|
|
duct_fan_pwmfreq: 5000Hz
|
|
duct_fan_off_spd: "0.0"
|
|
duct_fan_lo_spd: "1.0"
|
|
duct_fan_vent_spd: "50.0"
|
|
duct_fan_hi_spd: "100.0"
|
|
prjpwr_pin: GPIO19
|
|
prjpwr_name: Prj3 Pwr
|
|
dallas_pin: GPIO32
|
|
dallas_in_addr: "0x1F3C01D0756F0928"
|
|
dallas_in_name: Prj3 Temp In
|
|
dallas_prj_addr: "0x873C01D0756D4B28"
|
|
dallas_prj_name: Prj3 Temp Prj
|
|
dallas_out_addr: "0xA901143295610E28"
|
|
dallas_out_name: Prj3 Temp Out
|
|
dallas_update_interval: 30s
|
|
|
|
globals:
|
|
- id: duct_fan_off_spd
|
|
type: float
|
|
initial_value: ${duct_fan_off_spd}
|
|
- id: duct_fan_lo_spd
|
|
type: float
|
|
initial_value: ${duct_fan_lo_spd}
|
|
- id: duct_fan_vent_spd
|
|
type: float
|
|
initial_value: ${duct_fan_vent_spd}
|
|
- id: duct_fan_hi_spd
|
|
type: float
|
|
initial_value: ${duct_fan_hi_spd}
|
|
|
|
esphome:
|
|
name: prj3
|
|
platform: ESP32
|
|
board: esp32doit-devkit-v1
|
|
|
|
wifi:
|
|
ssid: "kungle-oss"
|
|
password: "hcfU8@gG&8Hm"
|
|
fast_connect: true
|
|
|
|
manual_ip:
|
|
static_ip: 192.168.35.192
|
|
gateway: 192.168.35.1
|
|
subnet: 255.255.255.0
|
|
|
|
# Enable fallback hotspot (captive portal) in case wifi connection fails
|
|
ap:
|
|
ssid: "Prj3 Fallback Hotspot"
|
|
password: "xfPfYSP3N0C3"
|
|
|
|
captive_portal:
|
|
|
|
# Enable logging
|
|
logger:
|
|
|
|
# Enable Home Assistant API
|
|
api:
|
|
|
|
ota:
|
|
|
|
switch:
|
|
- platform: template
|
|
name: Thermostat On
|
|
id: thermostat_on_id
|
|
optimistic: true
|
|
|
|
output:
|
|
- platform: ledc
|
|
pin: ${duct_fan_pin}
|
|
id: duct_fan_output_id
|
|
frequency: ${duct_fan_pwmfreq}
|
|
|
|
fan:
|
|
- platform: speed
|
|
id: duct_fan_spd_id
|
|
output: duct_fan_output_id
|
|
name: ${duct_fan_spd_name}
|
|
|
|
dallas:
|
|
- pin:
|
|
number: ${dallas_pin}
|
|
mode: INPUT_PULLUP
|
|
update_interval: ${dallas_update_interval}
|
|
|
|
sensor:
|
|
- platform: dallas
|
|
address: ${dallas_in_addr}
|
|
name: ${dallas_in_name}
|
|
id: dallas_in_id
|
|
- platform: dallas
|
|
address: ${dallas_prj_addr}
|
|
name: ${dallas_prj_name}
|
|
id: dallas_prj_id
|
|
- platform: dallas
|
|
address: ${dallas_out_addr}
|
|
name: ${dallas_out_name}
|
|
id: dallas_out_id
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin: ${prjpwr_pin}
|
|
name: ${prjpwr_name}
|
|
device_class: power
|
|
- platform: homeassistant
|
|
name: "Ventilate House"
|
|
entity_id: input_boolean.ventilate_house
|
|
id: ventilate_house
|
|
|
|
number:
|
|
- platform: template
|
|
id: duct_fan_target_spd_in
|
|
name: ${duct_fan_target_spd_in_name}
|
|
optimistic: true
|
|
min_value: ${duct_fan_lo_spd}
|
|
max_value: ${duct_fan_hi_spd}
|
|
step: 1
|
|
- platform: template
|
|
id: duct_fan_target_spd_prj
|
|
name: ${duct_fan_target_spd_prj_name}
|
|
min_value: ${duct_fan_off_spd}
|
|
max_value: ${duct_fan_hi_spd}
|
|
step: 1
|
|
set_action:
|
|
then:
|
|
lambda: |-
|
|
float lo_temp;
|
|
float hi_temp;
|
|
float curtemp;
|
|
float off_spd;
|
|
float lo_spd;
|
|
float vent_spd;
|
|
float hi_spd;
|
|
float newspd;
|
|
lo_temp = id(thermostat_prj_id).target_temperature_low;
|
|
hi_temp = id(thermostat_prj_id).target_temperature_high;
|
|
curtemp = id(dallas_prj_id).state;
|
|
off_spd = id(duct_fan_off_spd);
|
|
lo_spd = id(duct_fan_lo_spd);
|
|
vent_spd = id(duct_fan_vent_spd);
|
|
hi_spd = id(duct_fan_hi_spd);
|
|
ESP_LOGD("fan_speed", "DEBUG Ventilate House: %d", id(ventilate_house).state);
|
|
ESP_LOGD("fan_speed", "DEBUG Current Temp: %f", curtemp);
|
|
ESP_LOGD("fan_speed", "DEBUG Thermostat State: %d", id(thermostat_on_id).state);
|
|
if ((id(ventilate_house).state == false) &&
|
|
((curtemp < lo_temp) || (id(thermostat_on_id).state == false))) {
|
|
ESP_LOGD("fan_speed", "DEBUG turning off");
|
|
auto call = id(duct_fan_spd_id).turn_off();
|
|
call.perform();
|
|
return off_spd;
|
|
}
|
|
if (curtemp > hi_temp) {
|
|
ESP_LOGD("fan_speed", "DEBUG curtemp > hi_temp");
|
|
newspd = hi_spd;
|
|
} else {
|
|
// Set newspd to same linear proportion of spd range as current temp is of temp range
|
|
newspd = lo_spd + ((hi_spd - lo_spd) * (curtemp - lo_temp) / (hi_temp - lo_temp));
|
|
ESP_LOGD("fan_speed", "DEBUG New Speed set: %f", newspd);
|
|
}
|
|
if ((id(ventilate_house).state == true) && (newspd < vent_spd)) {
|
|
newspd = vent_spd;
|
|
ESP_LOGD("fan_speed", "DEBUG New Speed changed to Vent Speed: %f", newspd);
|
|
}
|
|
if (newspd < lo_spd) {
|
|
ESP_LOGD("fan_speed", "DEBUG New Speed under lo_spd, turning off");
|
|
auto call = id(duct_fan_spd_id).turn_off();
|
|
call.perform();
|
|
return off_spd;
|
|
}
|
|
ESP_LOGD("fan_speed", "DEBUG Setting fan to newspd: %f", newspd);
|
|
auto call = id(duct_fan_spd_id).turn_on();
|
|
call.set_speed(newspd);
|
|
call.perform();
|
|
return newspd;
|
|
- platform: template
|
|
id: duct_fan_target_spd_out
|
|
name: ${duct_fan_target_spd_out_name}
|
|
optimistic: true
|
|
min_value: ${duct_fan_off_spd}
|
|
max_value: ${duct_fan_hi_spd}
|
|
step: 1
|
|
|
|
# Dual-point thermostat
|
|
climate:
|
|
- platform: thermostat
|
|
id: thermostat_prj_id
|
|
name: Prj3 Prj
|
|
sensor: dallas_prj_id
|
|
visual:
|
|
min_temperature: 60 °F
|
|
max_temperature: 160 °F
|
|
temperature_step: 1
|
|
default_mode: auto
|
|
default_target_temperature_low: 78 °F
|
|
default_target_temperature_high: 160 °F
|
|
min_cooling_off_time: 60s
|
|
min_cooling_run_time: 60s
|
|
min_heating_off_time: 60s
|
|
min_heating_run_time: 60s
|
|
min_idle_time: 60s
|
|
heat_action:
|
|
- logger.log: "Turning off Prj3 Thermostat"
|
|
- switch.turn_off: thermostat_on_id
|
|
idle_action:
|
|
- logger.log: "Turning on Prj3 Thermostat"
|
|
- switch.turn_on: thermostat_on_id
|
|
cool_action:
|
|
- logger.log: "WARNING: Prj3 Thermostat has hit high temp!"
|
|
- switch.turn_on: thermostat_on_id
|
|
#TODO - provide some kind of warning / action here
|