esphome/_data/fountain-outside.yaml

substitutions:
  device_name: fountain-outside
  dn: fountain_outside
  friendly_name: Fountain Outside
  device_description: Energy Monitoring Smart Plug with button, blue LED, and red LED.

<<: !include .common.yaml
<<: !include .esp8266.yaml
<<: !include .wifi-oss.yaml

# Enable time component for use by daily power sensor
time:
  - platform: homeassistant
    id: homeassistant_time

binary_sensor:
  - platform: gpio
    pin:
      number: GPIO1
      mode: INPUT_PULLUP
      inverted: True
    name: ${friendly_name} button
    on_multi_click:
      - timing:
          - ON for at most 1s
          - OFF for at most 1s
          - ON for at most 1s
          - OFF for at least 0.2s
        then:
          - logger.log: "Double Clicked"
          - switch.toggle: relay2
      - timing:
          - ON for 1s to 2s
          - OFF for at least 0.5s
        then:
          - logger.log: "Single Long Clicked"
      - timing:
          - ON for at most 1s
          - OFF for at least 0.5s
        then:
          - logger.log: "Single Short Clicked"
          - switch.toggle: relay1

switch:
  - platform: gpio
    name: ${friendly_name} relay
    pin: GPIO12
    id: relay1
  - platform: gpio
    name: ${friendly_name} Light relay
    pin: GPIO14
    id: relay2

status_led:
  pin:
    number: GPIO3
    # inverted: yes

sensor:
  - platform: wifi_signal
    name: ${friendly_name} WiFi signal
    update_interval: 60s

  - platform: uptime
    name: ${friendly_name} uptime

# Reports the Current, Voltage, and Power used by the plugged-in device (not counting this plug's own usage of about 0.7W/0.02A, so subtract those when calibrating with this plugged into a Kill-A-Watt type meter)
  - platform: hlw8012
    sel_pin:
      number: GPIO13
      inverted: True
    cf_pin: GPIO4
    cf1_pin: GPIO5
    current_resistor: 0.001 #The value of the shunt resistor for current measurement. Defaults to the Sonoff POW’s value 0.001 ohm. Verified on https://fccid.io/2AKBP-X10S/Internal-Photos/X10S-Int-photo-4308983 that we use "R001" = 0.001 ohm
    voltage_divider: 2351 #The value of the voltage divider on the board as (R_upstream + R_downstream) / R_downstream. Defaults to the Sonoff POW’s value 2351. From the pic we use 2x "125" = 2x 1.2Mohm for R_upstream and "102" = 1kohm for R_downstream, so (1,200,000+1,200,000+1,000)/1,000 = 2401
    # but those don't fix the measurement values, probably because we actually have a BL0937 chip instead of a HLW8012, (and part variance aswell) so we have to manually calibrate with a known load or a load and a Kill-A-Watt type meter. My values used below will only be +/-10% of yours I think.
    # The comments about the voltage divider were taken from the AWP04L template. I was unable to verify the voltage divider in the Aoycocr X10S plug.
    power:
      name: ${friendly_name} Power
      unit_of_measurement: W
      id: wattage
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - 1379.1 -> 200.0 # Tested outdoor fountain pump via Kill-A-Watt
            - 2816.9 -> 411.0 # Tested blow-dryer low via Kill-A-Watt
            - 9250.6 -> 1341.0 # Tested water boiler via Kill-A-Watt
            - 10736.7 -> 1562.0 # Tested blow-dryer high via Kill-A-Watt
    current:
      name: ${friendly_name} Current
      unit_of_measurement: A
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - 2.07 -> 1.67 # Tested outdoor fountain pump via Kill-A-Watt
            - 4.18 -> 3.41 # Tested blow-dryer low via Kill-A-Watt
            - 14.37 -> 11.64 # Tested water boiler via Kill-A-Watt
            - 16.26 -> 13.12 # Tested blow-dryer high via Kill-A-Watt
    voltage:
      name: ${friendly_name} Voltage
      unit_of_measurement: V
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0
            - 355.9 -> 120.6 #Tested using a Kill-A-Watt meter, value while connected LED bulb was on
    # change_mode_every: 3 # 1 - Skips first reading after each change, so this will double the update interval. Default 8
    # update_interval: 3s # 10s - 20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s

# Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
  - platform: total_daily_energy
    name: ${friendly_name} Total Daily Energy
    power_id: wattage
    filters:
        - multiply: 0.001  ## convert Wh to kWh
    unit_of_measurement: kWh

text_sensor:
  - platform: version
    name: "Fountain 1 ESPHome version"